slot hole
英 [slɒt həʊl]
美 [slɑːt hoʊl]
网络 槽孔; 长孔; 切口
双语例句
- Contract: A container is a standard size and has feet that can slot into a hole on the roof of another container.
合约：集装箱具有标准尺寸，并且可以插入到另一个集装箱顶部的洞中。 - The bilateral slot walls of the shrinking bunch are respectively provided with a wall hole and an inclined salient wall is extended from the both sides of the subsidiary arm brace.
所述辅撑臂的两侧各往上延伸一斜状凸墙，所述斜状凸墙的前端段侧面各贯设一墙孔，而前段顶面各设置一撞击凸块； - Using CCD censor to receive the Laser diffraction and measure the precise slot width and round hole radius
利用CCD接收激光衍射的方法测量精密缝宽和圆孔直径 - Stability and Nonlinear Response of Drilling Shaft System in Deep Slot Hole Drilling
槽孔加工中钻杆系统的非线性运动与动力稳定性 - Under the same condition, the cooling effectiveness of the converging slot hole at the upstream of the throat is nearly always higher than that in the other locations.
在相同的主流入口雷诺数和二次流吹风比下，位于喉部上游位置的收敛缝形孔冷却效率大都高于其他位置。 - Compared with the cylindrical hole, the converging slot hole cooling effectiveness is improved obviously and more uniform in lateral variation in all locations.
与圆形孔相比，各位置处收敛缝形孔沿流向的冷却效率均得到有效改善，且在展向上的分布较均匀； - The results show that the converging slot hole cooling effectiveness in different locations all increases with the increase of the mainstream Reynolds number and coolant blowing ratio.
计算结果表明：各位置处收敛缝形孔吸力面的冷却效率随着吹风比和主流入口雷诺数的增大而逐渐升高； - Numerical simulation on the depth of transverse slot to film hole cooling performance "Templates for lettering and symbols& General principles, identification markings and the size of the slot widths"
横向槽宽度对气膜孔冷却性能数值研究GB/T16949-1997字体和符号模板基本要求、识别标记及槽宽尺寸 - There were three film cooling schemes used, namely, slot, discrete hole and wiggle strip.
采用的冷却方案共有3种，分别是缝隙式、离散孔式和波纹板式气膜冷却方案。 - Experimental Investigation on the Film-Cooling Adiabatic Effectiveness with Different Slot Inlet Hole Pitches
不同缝槽进气孔间距的纯气膜绝热温比试验研究 - A New Technology of Slot Cut of Middle Length Hole Post and Stall Method in Hard Ore
坚硬矿石内中深孔房柱法拉槽新工艺 - Interference Milling of Inner Multi Head Spiral Slot in Blind Hole
多头盲内螺旋槽的干涉铣削加工 - The stress on the flange ring slot is comparative high, the stress on screw hole is relative low.
法兰环槽根处的应力水平较高，螺栓孔周围的应力水平较低。 - This paper directs the slot and hole type carbonatite specific reservoir and reservoir geologic feature of tahe oilfield, and the main problems of current analysis well testing interpretation used in slot and hole type reservoir, unfold the finite element numerical well test application study.
本文针对塔河缝洞型碳酸盐岩油藏特殊的储层、油藏地质特征，以及现行解析试井解释方法在缝洞型油藏试井资料解释中面临的主要问题，开展了有限元数值试井新技术应用研究。 - Combined with the manufacture of copper staves, key problems of deep-hole and slot hole drilling are studied systematic in this paper, and a special system from process, tools and machining facilities used in copper staves deep-hole drilling is developed.
本文结合铜冷却壁制造技术，对深孔及特殊槽孔加工问题进行了系统的研究，开发出一套从工艺、刀具到加工设备的铜冷却壁专用深孔加工系统。 - Compared with the cascade without slot, the surface load of cascade with slot increases near the leading edge and trailing edge and decreases at the slot inlet. Experimental Investigation on the Film-Cooling Adiabatic Effectiveness with Different Slot Inlet Hole Pitches
通过开槽处理，改变了叶栅表面的静压分布，使叶栅前段、后段的负荷增大，小槽进口附近的负荷减小.不同缝槽进气孔间距的纯气膜绝热温比试验研究 - Research on liner Bump-pressure cementing technique of slot sidetracking slim hole Shan 7-10c
鄯7-10C侧钻小眼井尾管碰压固井技术研究 - Well Shan 7-10C is the first slot sidetracking directional hole and its successful drilling lays a foundation for slot sidetracking horizontal well.
鄯710C井是吐哈油田第一口套管开窗侧钻定向井，它的成功钻井，为套管开窗侧钻水平井奠定了基础。 - To Realize Intermittent Punch of Rotor Slot and Continuous Punch of Damping Hole at the Same Time
同时实现转子槽形间歇冲和阻尼孔连续冲的工艺介绍 - Based on this research background, an innovation converging slot hole ( console) film cooling configuration was studied in the present paper to further understand its flow and heat transfer characteristics.
本文以此为研究背景，对一种新型收敛缝形气膜孔冷却结构的流动和换热特性开展了数值和实验研究。